Air King B Series Manuel de service

307741Rev. RFirst choice whenquality counts.t03695AModel 220106 ShownINSTRUCTIONS-PARTS LISTINSTRUCTIONSThis manual contains importantwarnings and inf

10 307741ServiceWARNINGTo avoid serious injury and equipmentdamage, do not lift the equipment by theair motor lift ring if the total weight of theequi

11307741ServiceNOTE: Refer to Fig. 4 for steps 6 to 11.6. Remove the screws (31) and lockwashers (13)from the manifold (20).7. To prevent the spring-l

12 307741ServiceNOTE: Refer to Fig. 5 for steps 12 to 18.12. Remove the rubber pad (8) from the cylinder (36).Remove the trip rod bearing (37), using

13307741Service0370107283AFig. 53433403946454470354783766646536133134474007421A41

14 307741ServiceReassembly1. Clean all parts thoroughly and inspect for wear ordamage. Replace parts as necessary.NOTE: Refer to Fig. 6 for steps 2 to

15307741ServiceNOTE: Refer to Fig. 7 for steps 6 to 10.6. Grease the trip rod (40) with light, water-proofgrease and slide it into the piston (34) sha

16 307741ServiceNOTE: Refer to Fig. 8 for steps 11 to 16.11. Place the gasket (38*) on top of the cylinder (36).12. Thread the hub (10) onto the trip

17307741ServiceNOTE: Refer to Fig. 9 for steps 17 to 22.17. Lubricate the housing (18), spring (17), and guide(16) with light, water-proof grease. Ass

18 307741PartsModel 220106, Series AStandard Quiet Air Motor03696A256732686963622426232127285329*30820311319181716151412 11107654321*3883766*65*644344

19307741PartsModel 220106, Series AStandard Quiet Air MotorRefNo. Part No. Description QtyRefNo. Part No. Description Qty1 168184 SEAL, plate 22 176

2 307741Table of ContentsWarnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 5. . . . . . . . . . . . .

20 307741PartsModel 235525, Series BQuiet Air Motor03698A2568636224262327285329*30820311319181716151412 11107654321*3883766*65*644344*3113414745*46*39

21307741PartsModel 235525, Series BQuiet Air MotorRefNo. Part No. Description QtyRefNo. Part No. Description Qty1 168184 SEAL, plate 22 176536 PLATE

07420A2568696362242623275329*30820311319181716151412 11107654321*3883766*65*644344*3113414745*46*39403433*35*3676 77 7881838883798485868280, 81828770Y

23307741PartsModel 237000, Series AReduced Icing Quiet Air MotorRefNo. Part No. Description QtyRefNo. Part No. Description Qty1 168184 SEAL, plate 2

24 307741Dimensions03702036953/4 npsm(f) SwivelAir Inlet3/4 npt(f) SwivelAir Inlet03697Maximum Diameter: 305 mm (12”)1–1/4 npt Exhaust Port16 Exhaust

25307741Technical DataCategory DataMaximum Incoming Air Pressure 0.6 MPa, 6.2 bar (90 psi)Effective Piston Area 506 cm@ (78.5 sq. in.)Piston Diameter

26 307741Notes

27307741Notes

28 307741The Graco Standard WarrantyGraco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and wo

3307741WARNINGINJECTION HAZARDSpray from the gun/valve, hose leaks, or ruptured components can inject fluid into your body andcause extremely serious

4 307741WARNINGFIRE AND EXPLOSION HAZARDImproper grounding, poor ventilation, open flames or sparks can cause a hazardous condition andresult in a fir

5307741InstallationGeneral InformationNOTE: Reference numbers and letters in parenthesesin the text refer to the callouts in the figures and theparts

6 307741InstallationNoise ReductionInstruction Manual 307375 is supplied with this motor.It provides information on noise reduction.The following are

7307741TroubleshootingPressure Relief ProcedureWARNINGINJECTION HAZARDTo reduce the risk of serious injury, in-cluding fluid injection, splashing in t

8 307741TroubleshootingAir LeaksAir leaks are caused by worn or damaged gaskets orseals. To locate the leaks, first shut off the air supply tothe pump

9307741Troubleshooting03705AFig. 2D (30*)E (3)G (38*)F (33*)C (44*)*45, *46B (*35)*65H (15)K (26)29Model 220106 Shown12Pack cavity with light waterpro