Air King ESVAL30SS Manuel d'instructions télécharger pdf (Page 2)

INSTALLATION INSTRUCTIONS

CAUTION:

MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

STARTING INSTALLATION.

SECTION 1

Preparing the Range Hood

1. Unpack hood from the carton and conﬁrm that all pieces are present. In addition to the

range hood you should have:

2 - Chimney Sections

1 - Package containing:

1 - duct collar

2 - chimney brackets

8 - #6 x 1" mounting screws with wall anchors

2 - #6 x 3/8" self threading screws (chimney upper)

30" models: 2 - Aluminum Grease Filters (shipped installed)

36" models: 3 - Aluminum Grease Filters (shipped installed)

1 - GU24 Base, 26W Fluorescent Lamp

1 - Instruction/Safety Sheet

NOTE: Some hoods may be shipped with a protective plastic adhered to the range hood. It is

recommended to leave this in place during installation to protect the hood from scratching.

Remove when the installation is complete.

2. Lay the back side of the hood ﬂat on a table. Use a piece of cardboard to avoid damaging

the table or the hood.

3. Remove the lens cover on the underside of the range hood and install the included 26

watt ﬂuorescent lamp (Figure 1).

SECTION 2

Installing the Range Hood

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

STARTING INSTALLATION.

CAUTION:WHEN CUTTING OR DRILLING INTO WALL DO NOT DAMAGE

ELECTRICAL WIRING AND OTHER HIDDEN UTILITIES.

1. Locate and mark the upper keyhole positions on the wall. If installing onto drywall, drill

holes into wall using a 3/16" drill bit. Install wall anchors into the drilled holes (one for each

hole). Install (2) provided #6 x 1" screws, leaving a 1/8" gap between the screw head and

the wall. If installing into other material (brick, cement, plaster, etc.) choose an appropriate

fastner capable of supporting the weight of the hood. Line up the keyholes in the hood with

the screws and position in place. Hang the hood over the keyhole anchors and verify that the

hood is centered, plum and level (Figure 2).

www.airkinglimited.com

6728027 Rev. G 5-12 2 of 12

2. With the hood hanging in place from the top screws, mark the location of the lower holes.

If installing onto drywall, remove the hood and drill holes into wall using a 3/16" drill

bit. Install wall anchors into the drilled holes (one for each hole). If installing into other

material (brick, cement, plaster, etc.) choose an appropriate fastner capable of supporting

the weight of the hood. Hang the hood over the keyhole anchors and verify that the hood is

centered, level and the bottom holes line up with the anchors. Install the provided #6 x 1"

screws into the anchors (Figure 3). Tighten all screws completely and reinstall the Grease

ﬁlters. ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING CODES.

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

1. Install the included duct collar to the hood with two of the provided #6 blunt tip screws

(Figure 4).

1. Connect the ducting to the duct collar and secure in place using tape to seal all joints

(Figure 4).

NOTE: To achieve proper air ﬂow, 6" round ducting is required. The duct connector is 5.8" in

diameter (for 6" round ducting) and the center is located 3.1875" inches from the back wall.

CAUTION: ALWAYS DUCT THE FAN TO THE OUTSIDE THROUGH A WALL OR

ROOF CAP.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE IN ACCORDANCE

WITH LOCAL CODES, ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU ARE

UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE

SERVICES OF A QUALIFIED ELECTRICIAN.

1. Remove wire compartment cover by removing the screw then sliding it outward. Choose

the most convenient electrical knockout and remove using a straight-blade screw driver.

2. Run wiring from an approved source carrying the appropriate rating. One neutral (White), one

ground (green or bare copper), and one hot (Black). Secure the electrical wires to the wire

compartment with an approved electrical connector. Make sure you leave enough wiring in

the box to make the connection to the hood.

3. Connect the White wire from the range hood to the White wire from the supply, and the Black

wire from the range hood to the Black wire of the supply. Connect the ground wire from the

home (green or bare) and the Green wire from the range hood. Use approved methods for

all connections. Reinstall the wire compartment by sliding the tabs back into the holes then

reinstalling the screw that was removed eariler. Make sure all wiring is securely contained

within the wire compartment (Figure 5).

Figure 4

Duct Collar

Ducting

Hood

Figure 2

Upper Keyholes

Side View

Figure 3

Holes

Side View

Figure 1

Lamp

1 2 3 4 5 6 7 ... 11 12

Commentaires sur ces manuels

Pas de commentaire

Air King ESVAL30SS Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Hottes de cuisine Air King ESVAL30SS