READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFEGUARDS
CAUTION: To reduce the risk of fire and to properly exhaust air, be
sure to duct air outside - Do not vent exhaust air into spaces within
walls or ceilings or into attics, crawl spaces, or garages.
WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not
Use This Fan With Any Solid-State Speed Control Device.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTIC SHOCK
OR INJURY TO PERSONS OBSERVE THE FOLLOWING.
a) Use this unit only in the manner intended by the manufacturer.
If you have any question, contact the manufacturer.
b) Before servicing or cleaning unit, switch power to off at service
panel and lock the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
CAUTION: For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be done by qualified
person (s) in accordance with all applicable codes and standards,
including fire-related construction.
b) Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA) and
the American Society for Heating, Refrigeration, and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the outdoors.
e) If this unit is to be installed over a tub or shower, it must be
marked as appropriate for the application and be connected to a
GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.
f) NEVER place a switch where it can be reached from a tub or shower.
To ensure the best air and sound performance it is recommended
that the largest diameter ducting is used (5" or 6"). The length of
ducting and the number of elbows should be kept to a minimum.
To protect against condensation problems use insulated ducting.
Hard ducting will provide maximum air delivery. If using flexible
ducting always ensure it is pulled as tight as possible; using a short
section of flexible ducting in combination with hard ducting will
reduce noise transmission.
As an added convenience for installation you do not have remove
the Fan’s Blower assembly in order to install and wire this unit. You
can gain access to the fans wiring via the external wire
compartment shown in fig. 1. If you choose to wire from inside the
fan housing you will have to remove the fan’s blower assembly and
internal wiring compartment. The blower assembly is secured in
place with three # 8 sheet metal screws.
MOUNTING THE HOUSING
Select the best location to mount the housing in the ceiling. This fan
will require at least 8" of clearance in the ceiling will mount through
drywall up to
3
/4" thick. The fan housing can be mounted between
16" or 24" on center joists using the supplied four fan mounting
rails. Figure 2 shows housing installation between 16" or 24" on
center joists. Figure 3 shows housing installation directly to the joist
(16" on center).
16-24"
16-24"
GREEN
WHITE
BLACK (FAN)
PURPLE (LIGHT)
YELLOW (NIGHT LIGHT)
GREEN
YELLOW (NIGHT LIGHT)
PURPLE (LIGHT)
BLACK (FAN)
WHITE (FAN)
WHITE (LIGHT)
16-24"
INSTALLATION INSTRUCTIONS
AK80LSL / AK100LSL
Figure 1.
Figure 2.
Figure 3.
::bathroomsource
.
com
Call 1-800-667-8721 anywhere in the US and Canada
-
www.bathroomsource.com
Air King at
bathroom::accessories
U N L I M I T E D
Air King at
bathroom::accessories
(28 pages)
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels