Air King LIN Series Guide de dépannage télécharger pdf (Page 2)

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

STARTING INSTALLATION.

NOTE : When installing the Liner outdoors, the Air King Professional Liners are approved for

use in covered outdoor kitchens only. Proper duct adapters, ducting, chimneys, roof/wall

caps, etc. must be utilized as called out in the following instructions. Do not install the liner in

an uncovered area directly exposed to the elements.

SECTION 1

Preparing the Insert

1. Unpack hood from the carton and conﬁrm that all pieces are present. In addition to the

range hood you should have:

8 - Screws (LIN34, LIN40 models - 12; LIN46, LIN58 models - 14)

2 - Halogen Bulbs (LIN58 models - 4)

1 - Duct Adapter

1 - Grease Trough

2 - Grease Bafﬂes (LIN24, LIN46, LIN58 models - 3)

2 - Spacers (LIN24 models only)

1 - Instruction/Safety Sheet

NOTE: Some hoods may be shipped with a protective plastic adhered to the underside of the

unit. It is recommended to leave this in place during installation to protect it from scratching.

Remove when the installation is complete.

SECTION 2

Preparing the Area

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

STARTING INSTALLATION.

CAUTION: WHEN CUTTING OR DRILLING INTO WALL DO NOT DAMAGE

ELECTRICAL WIRING AND OTHER HIDDEN UTILITIES.

1. Cut an appropriately sized hole for the cabinet or canopy the liner will be mounted into

(Figure 1):

LIN24M models: 24.5" x 19.375" LIN24MD models: 24.5" x 22.625"

LIN28M models: 28.5" x 19.375" LIN28MD models: 28.5" x 22.625"

LIN34M models: 34.5" x 19.375" LIN34MD models: 34.5" x 22.625"

LIN40M models: 40.5" x 19.375" LIN40MD models: 40.5" x 22.625"

LIN46MD models: 46.5" x 22.625" LIN58MD models: 58.5" x 22.625"

NOTE: The hood must be mounted a minimum of 24" and a maximum of 36" from the

cooking surface.

SECTION 3

Mounting the Liner

CAUTION: DUE TO THE WEIGHT AND BULK OF THE UNIT, IT IS RECOMMENDED

THAT THREE PEOPLE ARE PRESENT DURING INSTALLATION TO LIFT, HOLD, AND SECURE

THE UNIT IN PLACE.

1. Lift unit up into position so that the bottom ﬂanges are in solid contact with the bottom of

the canopy or cabinet. Using the included wood mounting screws, secure the unit to the

canopy or cabinet by driving the screws through the holes (Figure 2).

www.airkinglimited.com

6728024M Rev. D 9-12 2 of 12

NOTE: If additional support is required, install a 2" x .75" strip of wood between the back of

the canopy (rear wall) and the hood. When installing the wood strip to the back of the canopy,

locate studs in the wall to support the weight of the canopy. Center the wood strip 11.5"

from the bottom of the canopy and attach the strip to at least two studs in the rear wall (do

not fasten the strip to drywall only). Lift unit up into position so that the bottom ﬂanges are in

solid contact with the bottom of the canopy or cabinet. Using wood screws and washers (not

included) secure the hood to the wood strip through the two keyholes in the back of the hood.

Using the included wood mounting screws, secure the unit to the canopy or cabinet by driving

the screws through the holes (Figure 3).

SECTION 4

Ducting

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL

BUILDING CODES.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

1. Determine the type of ducting you will require (Figure 4).

NOTE: For models using the B300, B500, and B600 blowers, a minimum of 6" diameter outlet

adapter & ducting is required to achieve the proper air ﬂow. The B900 requires a minimum of 8"

diameter adapter and ducting. The B1125 requires a minimum 10" diameter adapter and ducting.

NOTE: When the duct termination is similar to that shown in Figure 4 (passing through the wall

to which the hood is mounted) the installation requires special consideration. Depending upon

where the wall studs are located, it may be necessary to cut one or more of the wall studs and

install a header and footer to transfer the load to the adjacent studs. Additional studs may need

to be framed into the opening to attach dry wall or secure the hood. If this is your situation Air

King recommends that you hire a professional and comply with all applicable codes.

2. Install the proper sized outlet adapter to the hood by matching up the four holes on the

ﬂange of the adapter to the four corresponding holes on the hood and secure in place

with the provided screws. Ensure an airtight seal around the adapter by securing all

connections with ducting tape (Figure 5).

Figure 4

Wall Cap

Outlet

Adapter

Roof Cap

Horizontal

Vertical

Figure 1

24.5"/28.5"/34.5"/

40.5"/ 46.5"/58.5"

19.375"

22.625"

Figure 2

Screws

Flange

Canopy

Washer

Figure 3

Canopy

Wood

Mounting

Strip

OPTIONAL ADDITIONAL SUPPORT

Screws

Flange

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Air King LIN Series Guide de dépannage Page 2

Commentaires sur ces manuels