Air-king 9520 Manuel d'utilisateur télécharger pdf

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOUR-

SELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

20" I-BEAM MOUNT FAN

20" (50.8 cm) MODEL 9520

OPERATING INSTRUCTIONS & PARTS MANUAL

DESCRIPTION

The Air King

20" (50.8 cm) I-Beam mount fan features 3-speed pull cord

operation and a 3-paddle fan blade. This fan has a permanently lubricated

motor with a 9 ft. (2.74 m) 18/3 cord set and is constructed of sturdy,

powder coated steel.

SPECIFICATIONS

Motor ...................................... 120 V, 50/60 Hz

Blade diameter ........................ 20" (50.8 cm) Model 9520

Speeds .................................... 3

Control..................................... Pull Cord

Air ow distribution .................. 360°

Approvals................................. UL/ETL Listed. Close mesh fan guard

meets OSHA requirements.....................

GENERAL SAFETY INFORMATION

1. Make certain that the power source conforms to the electrical

require

ments of the fan.

2. The power cord is equipped with a three-prong grounded plug that

must be inserted into a matching receptacle. Under no circumstances

should the grounding prong be cut off the plug. Where a two-prong wall

receptacle is encountered, it must be replaced with a properly grounded

three-prong receptacle installed in accordance with the National Electrical

Code (NEC) and all applicable local codes and ordinances. This work

must be done only by a qualied electrician, using copper wire only.

WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS

NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE THE

RISK OF ELECTRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT

PERMITTED IN CANADA.

3. Where possible, avoid the use of extension cords. If they must be used,

minimize the risk of overheating by ensuring that they are UL listed and

of the proper gauge and length. Never use a single extension cord to

operate more than one fan.

4. Do not insert ngers or foreign objects into the fan. Do not block or

tamper with the fan in any manner while it is in operation. Do not touch

the fan while in operation or just after it has been turned off, as some

parts may be hot enough to cause injury.

5. Unplug power cord before installing or servicing the fan.

WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE

SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR

SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD.

6. This fan is intended for general use ONLY. It must NOT be used in

potentially dangerous locations such as ammable, explosive, chemical

laden or wet atmospheres.

7. DO NOT mount fan near windows or bay doors. Rain may create an

electrical hazard.

8. Completely reassemble fan, according to instructions before

reconnecting to power supply.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE

THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE.

WARNING: THIS PLUG IS A SAFETY FEATURE, TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK AND PERSONAL INJURY. DO NOT REMOVE, REPLACE,

REPAIR OR TAMPER WITH THE ORIGINALLY SUPPLIED PLUG. IF THE FAN DOES

NOT FUNCTION PROPERLY, IT MAY BE DUE TO THE SAFETY DEVICE INCOR-

PORATED IN THIS PLUG. RETURN TO AN AUTHORIZED SERVICE CENTER

OR CALL 800-233-0268, MONDAY - FRIDAY, BETWEEN 8:00 A.M. AND 5:00

P.M. EST. IF THE PLUG WARNING LABEL IS MISSING OR DAMAGED, CALL

THE TOLL FREE NUMBER FOR A REPLACEMENT LABEL.

MODEL

9520

SPEED

HIGH MED LOW

CFM 7510 5010 3735

/s 3.54 2.36 1.76

RPM 1560 1041 776

Amps 1.78 1.46 1.02

Watts 207 167 115

dB A 62 55 48

WARNING: BECAUSE OF SIZE AND WEIGHT OF THIS FAN, MAKE

SURE ALL PARTS ARE COMPLETELY ASSEMBLED ACCORDING TO

INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN FAN COMING

APART DURING OPERATION AND/OR PERSONAL INJURY.

I-BEAM MOUNT INSTALLATION

1. Locate the L-shaped pipe to the desired location on the I-Beam ange.

Install the 5/16 x 2" U-Bolt over the pipe and through the clamping plate

holes. The at part of the clamping plate ts on the I-Beam ange and

the end with the slight bend goes against the pipe. Install at washer,

lock washer and nuts. Finger tighten the nuts on the U-Bolt. (Figure 1)

2. Slide the clamping plate onto I-Beam ange until U-Bolts contact

ange.

3. Adjust L-shaped pipe so forward clamp plate is as close to the label

at the bend as possible.

4. Tighten nuts on bolt so pipe does not move.

5. Screw on the adapter mount as far as it will go on to the L-shaped

pipe. Tighten set screw in pipe coupling with provided allen key.

6. Align Yoke with grill mounting threads. Loosely attach one Grill Knob

and one Rubber Spacer to the Head Assembly. Attach the other Grill

Knob and Rubber Spacer to the Head Assembly and FIRMLY tighten.

Return to the rst Grill Knob and FIRMLY tighten. (Figure 2)

5084037Rev. A 9/07

5/16 Nut

5/16 Lock

Washer

5/16 Flat

Washer

1/4" Set Screw

Tighten

Bolt

Yoke

Fan Head

Figure 1

U-Bolts

Tighten Clamp

Plate Here

9. This Fan is not suitable for use in hazardous locations. Please refer to

National Electric Code (NEC) Article 500 or applicable state or local

codes or standards relating to electrical requirements for Hazardous

locations. THIS FAN DOES NOT MEET THE REQUIRMENTS OF

NEC ARTICLE 500 (2002).

Commerical Style Fan

WARNING: This fan should be used only in a clean, dry

environment. Mounting of this product in any way other then

specied in the instruction sheet will null and void the

manufacturer's warranty.

1 2

Résumé du contenu

Page 1 - 20" I-BEAM MOUNT FAN

READ AND SAVE THESE INSTRUCTIONSREAD CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOUR-SELF A

Page 2 - LIMITED WARRANTY

MODEL 95205084037Rev. A 9/072SecondarySupportCableFigure 4OPERATION1. Plug in cord and select desired operating speed with pull cord.2. WARNING: T

Commentaires sur ces manuels

Pas de commentaire

Air-king 9520 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Fax Air-king 9520. Air King 9520 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Fax Air-king 9520